Age estimation of different tree species using a special kind of an electrically recording resistance drill

The determination of tree age is an important issue for urban green planning, forestry and dendrology; finding non-destructive and quasi-non-destructive methods for this purpose is of great theoretical and practical importance. The resistance drilling method is quasi-non-destructive because the average diameter of an opening that remains after drilling does not exceed 3 mm. Do electrically recording resistance drills allow precise assessment of tree age? The aim of this study is to assess the accuracy of determining the number of tree rings based on an examination of this special kind of drilling resistance profiles for three tree species, the pine Pinus sylvestris L., the oak Quercus robur L., and the birch Betula pendula ROTH. In 2015 and 2016, 15 pine trees, 15 oak trees, and 15 birch trees were randomly selected. For each studied tree, a measurement was conducted using the electrically recording resistance drill IML-Resi E400 with a flat-tipped 1.5/3 mm steel needle (research sample), and an increment core was taken (reference sample). The drill used was not a real Resistograph^®. The analysis of the E400-profiles underestimated the number of tree rings; the mean bias error (MBE) values were –6.5, –2.5, and –6.0 years for pine, oak, and birch, respectively. The proportion of investigated trees with less than five years difference between the research and reference samples varied from 38.4 (birch) to 66.7 (oak) percent. The accuracy of tree age determination was lowest for birch and highest for oak. The binomial generalised linear model (GLM) revealed that the most accurate tree age assessments were obtained from tree rings wider than 2 mm. The measurements clearly showed that the electrically recording resistance drill IML-Resi E400 enables a quick, although approximate, tree age assessment. Future research should concentrate on electronically regulating and recording drills, providing a higher spatial and signal resolution, and a stronger correlation to wood density.     

菠萝蜜种子淀粉制备香草兰微胶囊的工艺研究

以菠萝蜜种子淀粉为壁材,采用饱和水溶液法制备香草兰精油微胶囊,以包埋产率为指标,采用响应面分析法对微胶囊的包埋条件进行优化探讨。结果表明:5个单因素中,影响最显著的因素为壁芯材比例、包埋温度和包埋时间。响应面优化得到香草兰精油微胶囊的最佳工艺条件为壁芯材比例为7.5∶1;包埋时间72 min;包埋温度54℃,此条件下的包埋产率为(95.46±0.2)%,包埋率为(76.35±0.6)%,载油量为(27.73±0.3)%。试验证明,此条件结果与模型预测值相吻合,此工艺条件可为菠萝蜜种子淀粉包埋香草兰精油微胶囊工艺提供理论依据。     

A new lean no time test baking method with improved discriminating power

In response to customer concerns related to gluten strength in commercial baking, the Canadian Grain Commission assessed whether the Canadian Short Process (CSP) test bake method was generating useful data related to intrinsic strength of wheat varieties. Assessment of CSP loaf volume data for Canadian variety trials spanning 2003 to 2013 showed very little correlation with dough strength parameters as measured by farinograph and extensigraph. A lean no time (LNT) test baking method was developed that can better discriminate genotypes and provide objective indicators of the effect of intrinsic dough strength on baking quality. From early method development, through method validation and verification using diverse sets of samples targeting different Canadian wheat classes and grown in three different crop years, results showed the LNT method to be more discriminating and easily adopted by other laboratories. In 2015, the LNT method was adopted as the method of choice in future Canadian variety registration trials. The LNT method is fast, simple and well-suited to high throughput test baking conditions encountered in the evaluation of large numbers of breeder lines. A new objective parameter, loaf top ratio, was also introduced and found to correlate well with dough strength and dough handling properties.     

农产品中农药残留检测技术研究进展

通过综述农产品农药残留现状及检测技术研究进展,分析比较有关农产品农药残留的国内外标准,指出我国农药残留标准存在的一些问题,并对有关检测技术提出建议。     

沉淀法制备的紫杉醇白蛋白微粒包封率测定

采用沉淀法制备紫杉醇白蛋白微粒,采用高效液相色谱法(HPLC)测定紫杉醇质量浓度,以二氯甲烷为有机相,采用萃取法分离白蛋白微粒与游离药物,测定其包封率。结果表明:紫杉醇在10~100 mg·L-1范围内线性良好,平均回收率可达到97.6%~101.0%;有机溶剂萃取法测定紫杉醇白蛋白微粒包封率的平均回收率,达94.80%~101.67%。这种方法测定紫杉醇白蛋白微粒回收率准确可靠,适用于沉淀法制备的白蛋白微粒的包封率测定。     

全银杏粉饮料配方的模糊数学法优化及其稳定性研究

为解决泰州大佛指银杏加工季节限制，获得一款口感宜人、稳定性良好的保健型饮料，以全银杏粉为主要原料，通过模糊数学法结合正交试验优化全银杏粉饮料的最佳配方，采用功效系数法结合正交试验优化全银杏粉饮料稳定剂的最佳复配比，以均质压力和均质温度对全银杏粉饮料稳定性的影响确定最佳均质条件。结果表明，全银杏粉饮料的最佳配方为：全银杏粉初汁添加量80%，低聚果糖添加量10%，柠檬酸添加量0.10%，蜂蜜添加量0.10%；稳定剂最佳复配比为：微晶纤维素（MCC）0.15%，卡拉胶0.20%，海藻酸丙二醇酯（PGA）0.20%；最佳均质条件为：均质压力40 MPa，均质温度60 ℃。     

基于无人机LiDAR的天然林与人工林林隙提取

为研究主动遥感进行森林地物分类和林隙提取的效果,分别在天然林和人工林中比较了无人机激光雷达(Li DAR)数据的阈值法、逐像元法和面向对象法3种方法的分类精度和适用性。选取天然林(黑龙江省哈尔滨市帽儿山林场)和人工林(内蒙古自治区赤峰市旺业甸林场)两处试验区,应用阈值法、逐像元法和面向对象法3种方法,对两个试验区采集的无人机Li DAR数据进行林隙、非林隙、其他类型划分。研究结果表明,面向对象法在天然林和人工林试验区中的分类精度和Kappa系数均最高,天然林为82. 43%、0. 73,人工林为91. 74%、0. 88;逐像元法次之,天然林为76. 62%、0. 64,人工林为78. 68%、0. 68;阈值法的分类精度和Kappa系数差异较大,在天然林中的精度极低,为50. 54%、0. 27,人工林的精度较高,为79. 12%、0. 69。面向对象法和逐像元法在天然林和人工林普遍适用,均可以达到理想的分类精度和Kappa系数。阈值法在天然林的精度较低,更适合于人工林的分类,即林分高度趋于一致,且建筑、道路等其他类型干扰较少的区域。天然林的最佳分类方法为面向对象法,人工林的最佳分类方法为阈值法。     

漆酶LAC表达与鸭梨果心褐变的关系

【目的】探究在不同成熟度和降温贮藏方式下,LAC表达模式与鸭梨果心褐变的关系,为进一步解析鸭梨果心褐变机制提供理论依据。【方法】以鸭梨作为材料,通过对不同成熟度（早采、中采和晚采）的鸭梨进行急速降温（急降）和缓慢降温（缓降）处理,观察贮藏期间鸭梨果心褐变情况,测定漆酶（Laccase,LAC）活性及其基因LAC的相对表达量,研究LAC在鸭梨果心褐变过程中的参与作用。【结果】冷藏60 d时,晚采鸭梨出现褐变,晚采缓降处理的鸭梨果心褐变指数为0.32,是同期急速降温处理的2.56倍;在贮藏90 d时,中采缓降处理的褐变指数是0.24,中采急降处理的褐变指数仅为0.01。各个处理组在贮藏期间LAC活性多数表现为先逐渐升高后下降的趋势,晚采的果实在贮藏60 d时出现活性高峰,褐变发生;早采和中采鸭梨LAC活性高峰均在90 d时出现,褐变程度低于晚采鸭梨。在贮藏期间,缓慢降温处理的LAC活性高于急速降温处理。鸭梨LAC14和LAC7表达量呈先上升后下降的趋势,LAC6表现为先下降后上升再降低的变化趋势;中采、晚采鸭梨在贮藏60 d时,LAC14和LAC7表达量最高。【结论】与缓慢降温相比,急速降温处理减少了鸭梨果心褐变的发生。在整个贮藏期间,LAC活性呈先上升后下降然后又上升的趋势,其峰值时的活性高低次序为：晚采>中采>早采,这与果心褐变趋势一致;LAC在鸭梨果心褐变过程中上调表达。相比缓慢降温处理,急速降温处理具有较低的LAC7、LAC14和LAC6表达量。急速降温结合适时采收能够抑制LAC的上调表达,减少鸭梨果心褐变发生。     

高抗氧化活性lager型啤酒酵母选育

采用过氧化氢刺激lager型啤酒酵母,Tadpoling法筛选细胞活力恢复较快突变菌,根据各菌株线粒体膜电位、胞内氧自由基(ROS)水平筛选获得4株活性较高菌株。比较突变菌与原始菌传代发酵性能、胞内ROS、活力指标及每一代细胞死亡率水平,最终获得一株抗氧化能力提高且活力稳定性较高啤酒酵母菌株。分析验证突变菌线粒体DNA修复相关基因MHR1发现,该基因发生部分碱基突变。     

基于综合判别法的广东省水土流失状况遥感分析

以2009和2010年10 m分辨率的ALOS多光谱遥感影像为数据源,采用计算机自动分析与人机交互判别相结合的方法,对广东省水土流失状况进行了遥感分析。结果表明:广东省土地利用以林草地、水田、建筑用地、水域和旱地为主,植被覆盖状况良好,珠三角和粤西地区地形平缓,粤北山区地形起伏较大;全省水土流失总面积20945.87 km 2,其中自然侵蚀面积14781.06 km 2,人为侵蚀面积6164.81 km 2;全省水土流失以轻度和中度侵蚀为主,主要分布在河源、梅州和云浮等地,其中生产建设活动导致的人为侵蚀集中分布在惠州、清远和广州等地。